Most medical and surgical devices used in healthcare facilities are made of materials that are heat stable and therefore undergo heat, primarily steam, sterilization. However, since 1950, the number of medical tools and gadgets composed of materials (like plastics) that need to be sterilized at low temperatures has increased. Since the 1950s, ethylene oxide gas has been utilized for medical devices that are sensitive to heat and moisture. Within the past 15 years, a number of new, low-temperature sterilization systems (e.g., hydrogen peroxide gas plasma, peracetic acid immersion, ozone) have been developed and are being used to sterilize medical devices.
Sterilization destroys all microorganisms on the surface of an article or in a fluid to prevent disease transmission associated with the use of that item. While the use of inadequately sterilized critical items represents a high risk of transmitting pathogens, the documented transmission of pathogens associated with an inadequately sterilized critical item is exceedingly rare.
The concept of what constitutes “sterile” is measured as the probability of sterility for each item to be sterilized. This probability is commonly referred to as the sterility assurance level (SAL) of the product and is defined as the probability of a single viable microorganism occurring on a product after sterilization. SAL is normally expressed as a 10−n.
Medical devices that have contact with sterile body tissues or fluids are considered critical items. These items should be sterile when used because any microbial contamination could result in disease transmission. Such items include surgical instruments, biopsy forceps, and implanted medical devices.
Steam Sterilization
Of all the methods available for sterilization, moist heat in the form of saturated steam under pressure is the most widely used and the most dependable. Steam sterilization is nontoxic, inexpensive, rapidly microbicidal, sporicidal, and rapidly heats and penetrates fabrics.
The fundamental idea behind steam sterilization in an autoclave is to subject every object to direct steam contact for the designated amount of time at the necessary temperature and pressure.
The two basic types of steam sterilizers (autoclaves) are the gravity displacement autoclave and the high-speed pre-vacuum sterilizer.
For gravity displacement sterilizers the penetration time into porous items is prolonged because of incomplete air elimination. The high-speed pre-vacuum sterilizers are similar to the gravity displacement sterilizers except they are fitted with a vacuum pump (or ejector) to ensure air removal from the sterilizing chamber and load before the steam is admitted.
Flash Sterilization
“Flash” steam sterilization was originally defined by Underwood and Perkins as sterilization of an unwrapped object at 132°C for 3 minutes at 27-28 lbs. of pressure in a gravity displacement sterilizer.
Currently, the time required for flash sterilization depends on the type of sterilizer and the type of item.
Flash sterilization is a modification of conventional steam sterilization (either gravity, pre-vacuum, or steam-flush pressure-pulse) in which the flashed item is placed in an open tray or is placed in a specially designed, covered, rigid container to allow for rapid penetration of steam.
Flash sterilization is considered acceptable for processing cleaned patient-care items that cannot be packaged, sterilized, and stored before use. It also is used when there is insufficient time to sterilize an item by the preferred package method. A few adverse events have been associated with flash sterilization. Flash sterilization should not be used for reasons of convenience, as an alternative to purchasing additional instrument sets, or to save time.
Low-Temperature Sterilization Technologies
Ethylene oxide (ETO) has been widely used as a low-temperature sterilant since the 1950s. It has been the most commonly used process for sterilizing temperature- and moisture-sensitive medical devices and supplies in healthcare institutions in the United States. Two types of ETO sterilizers are available, mixed gas and 100% ETO.
For several reasons, healthcare personnel have been exploring the use of new low-temperature sterilization technologies for ETO with chlorofluorocarbon that are currently available and cleared by the FDA for medical equipment including 100% ETO; ETO with a different stabilizing gas, such as carbon dioxide or hydrochlorofluorocarbons (HCFC); immersion in peracetic acid; hydrogen peroxide gas plasma; and ozone.
Sterilizing Practices
The delivery of sterile products for use in patient care depends not only on the effectiveness of the sterilization process but also on the unit design, decontamination, disassembling and packaging of the device, loading the sterilizer, monitoring, sterilant quality, and quantity, and the appropriateness of the cycle for the load contents, and other aspects of device reprocessing.
Healthcare personnel should perform most cleaning, disinfecting, and sterilizing of patient-care supplies in a central processing department in order to more easily control quality. The aim of central processing is the orderly processing of medical and surgical instruments to protect patients from infections while minimizing risks to staff and preserving the value of the items being reprocessed.

